We've encountered this great article involving Tools You Need to Install a New Bathtub directly below on the web and reckoned it made sense to write about it with you on this site.
Setting up a bath tub isn't specifically rocket science, but it does require strong plumbing, carpentry, and also occasionally, tiling skills. Replacing an old tub with a new one is additionally a reasonably tough task. If the old bathtub is readily accessible, the project can move quickly; if you need to open a wall surface to eliminate the old bathtub and position the brand-new tub, the task is much harder. In either instance, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub and also set in the new one. Make certain you have actually certified yourself for the work and are comfortable attempting it. Instead of working with a professional to take over a halfway-completed job, it is much better to think about using one prior to you begin. Possibilities are you might need an expert plumber to make tube connections.
This article will certainly assist you mount a brand-new bath tub in your restroom if you have actually already purchased a new tub and also do not need to transform the setup of your previous water system pipelines.
Your devices and also material checklist must make up the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is separate the water system. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the limited accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to proceeding to fit the new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making sure that the washers remain in area in between the faucet and also the sink. Protect the tap in place with the supplier provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The previous type should be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using both wood boards under its feet, put the tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The following objective is to make certain that the tub is leveled all round. This can be achieved by examining the level and also adjusting the feet on the tub up until the level reviews degree.
To set up taps, fit the bottom of the furthest flexible faucet connector to the suitable supply pipe by making a compression join; after that do the same for the various other tap.
Switch on the water system as well as inspect all joints and new pipework for leaks as well as tighten them if needed. Fill up the bathtub as well as likewise inspect the overflow outlet and the typical outlet for leaks.
Ultimately, take care of the bath paneling as explained in the maker's instruction manual. Tiling and securing around the bathtub should wait till the tub has been made use of a minimum of once as this will certainly resolve it right into its last position.
Getting ready for the Installment
Firstly, the sustaining framework provided with the bathroom must be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid stress on the tub.
Fit the flexible tap ports to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to fracture an inflexible seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, leading to problems with moisture and possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and also fittings. They are sold in tubes as well as cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to permit the activity experienced when the tub is in use. The sealant can crack relatively very early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or waterproof glue as well as cement.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
As a fervent person who reads about How to Install a Bathtub, I thought sharing that section was smart. If you enjoyed our blog post please be sure to share it. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Start Now